关闭测试开关Switch OFF
接线或安装灯具前，确认测试开关处于“关”。
Before wiring or fitting a lamp, make sure the test switch is OFF.
SPLT Support
SPLT 售后支持与使用指南 SPLT Support & User Guide
SPLT00、SPLT01、SPLT04 快速试灯盒系列的说明书、快速操作、型号差异、参数解读与常见故障排查。
Manuals, quick operation, model differences, readings and troubleshooting for the SPLT00, SPLT01 and SPLT04 series.
Manuals
SPLT 说明书下载SPLT Manuals
下载当前有效的 SPLT 中英文说明书。产品参数与安全要求以随机说明书和机身标识为准。
Download the current SPLT manuals. Follow the shipped manual and product markings for specifications and safety.
Quick start
快速使用Quick Operation
接入被测品Connect the load
将被测品接到 E14、E27、B22、线夹、接线柱或 AC 插座；同一时间只使用一路。
Connect through E14, E27, B22, clips, binding posts or the AC outlet. Use one output path at a time.
通电观察结果Power and observe
把开关拨到“开”：SPLT00 观察是否点亮；SPLT01 查看电压/功率与报警；SPLT04 读取 V/A/W/PF。
Switch ON: observe lighting on SPLT00, voltage/power and alarms on SPLT01, or V/A/W/PF on SPLT04.
关闭后取下Switch OFF before removal
测试完成后先关闭开关，再取下灯具或拆除线夹。
After testing, switch OFF before removing the lamp or clips.
Readings
型号差异与读数Models and Readings
SPLT00
无表头，用于快速通电试亮。
No meter; for quick lighting checks.
SPLT01
显示交流电压/功率，可学习基准功率并设置 ±5%～±20% 超差报警。
Shows AC voltage/power with learned reference and ±5–20% tolerance alarms.
SPLT04
同时观察交流电压、电流、有功功率和功率因数。
Shows AC voltage, current, active power and power factor together.
Troubleshooting
常见故障排查Common Troubleshooting
打开开关后整机不亮No display after switching on
先断电检查插座、电源线、开关与保险丝。保险丝只能更换为机身原配同类型、同额定值规格。
Disconnect power and check the outlet, cord, switch and fuse. Replace only with the same type and rating fitted to the product.
通电不良或接触不稳Unstable power or contact
保险丝多次烧断后，保险丝座触点可能烧蚀，应更换整个保险丝座。
Repeated fuse failures may damage the holder contacts. Replace the complete fuse holder.
有电压但灯不亮Voltage present but lamp is off
检查灯头是否拧紧、灯具是否损坏，以及线夹是否夹牢。
Check that the lamp is seated, the lamp is functional, and the clips are secure.
功率读数缓慢下降Power slowly decreases
多由灯具升温后真实功率下降造成，通常不是 SPLT 故障。
This often reflects the lamp's real power falling as it heats, rather than a SPLT fault.
Safety
安全注意Safety Notes
输出端为交流市电Outputs carry AC mains
测试开关处于“开”时，灯座、线夹、接线柱和 AC 负载接口均可能带电，禁止触碰金属接触点。
When the switch is ON, lamp sockets, clips, binding posts and the AC load outlet may be live. Never touch metal contacts.
所有接线必须断电操作Power off before handling
接线、取灯、换保险丝或维修前，先关闭开关并断开输入电源。
Switch off and disconnect input power before wiring, removing lamps, replacing the fuse or servicing.
Product
返回 SPLT 产品页Back to SPLT
查看产品参数、接口与现场图片。
See product specifications, interfaces and photos.
打开产品页Open product page